Nitrogen flow meter supplier | What is Lind GmbH in Germany | Flow meter distributor

Flow Meters – Silver Automation Instruments

『nitrogen flow meter supplier|flow meter distributor』Related information(clamp on meter|electromagnetic meter|venturi meterrotameter|orifice meter|ultrasonic flow meter|mass flow meter|coriolis mass flow meter|coriolis flow meter|magnetic flow meter|magmeter flow meter|magflow flow meter|mag meter flow meter|electromagnetic flow meter|vortex flow meter|turbine flow meter|thermal mass flow meter|thermal flow meter|rotameter flow meter)

1. Someone who understands the English language of valve technology can help.

Isnt it easy? Look at my translation. If possible, you can adopt my answer. Oh~~!! Titanium Valves: 1. General shall not, without permission Party casting welding repair process. 2. Material forged titanium material shall be ASTM B381 Gr. F2, or Gr. F3. Casting titanium material shall be ASTM B367 Gr. C2, or Gr. C3. Titanium components, the maximum iron content of 0.07% and the maximum hydrogen capacity of 60ppm. Casting the mechanical properties of casting residue to comply with ASTM requirements. Stick Titanium Standard ASTM B348 Gr.5. 3. X-ray detection casting is subject to 100% X-ray detection test, based on ASTM E446 Class A, B, C 2-class standards, with no D, E, F. 4. Penetrant testing all the casting in the stress test carried out after the required 100% of the permeability test, in order to avoid casting the cracks, trachoma and so on. 5. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents.  Hastelloy alloy valve 1. Castings Hastelloy Castings Hastelloy C4 and the need to use ASTM A494 Grade CW-2M of the alloy, the largest iron content does not exceed 2%. If you specify the use of Hastelloy C276, Ze Xu using UNS N10276 alloy, mechanical properties required to meet the ASTM minimum requirements. 2. X-ray detection for each casting is subject to ultrasonic or X-ray detection. After each batch and then take 10% of the testing, the nominal diameter greater than or equal 6 "of the body in need of complete testing, greater than or equal 8" in key parts of the body just for testing. -Ray flaw detection test based on ASTM E446 Class A, B, C 2-class

nitrogen flow meter supplier|flow meter distributor

standards, with no D, E, F. If you have casting did not meet testing standards be admitted to the batch number of the additional testing. If these two happen again does not meet state testing standards, then take all of the batch for testing. 3. Penetrant testing a batch of each supplier is required to provide penetration testing report at the same time need to provide mechanical tests, physical tests and chemical composition of reports. 4. Certificate B must provide a detailed mechanical performance testing, physical testing, chemical composition of reports and documents.  dual-phase steel valves: 1. A dual-phase steel all of the components required to meet the ASME V111, Div 1, Appendix 7 requirements. 2. Material Duplex steel castings for example, to comply with ASTM A995 Grade 4A for 2205 alloy, grade 6A for the 2507 alloy. Chemical composition, mechanical properties to meet the requirements of subparagraphs 3 to 5. 3. Chemical composition of the amount of corrosion-resistant duplex steel (PREN) according to the formula: PREN = (Cr wt% + 3.3 Mo wt% + 16 N wt%), calculate the value of not less than the following. 2205 Alloy - 34 2507 Alloy - 40 4. Chemical composition requirements are as follows Material 2205 Alloy 2507 Alloy maximum carbon content of 0.030% 0.030% chromium content of 21.5-23% 24-26% nickel content of 4.5-6.5% 5.5-8.0% Mo content of 2.9 -3.5% nitrogen content of 0.145-0.2% 3.6-4.0% 0.24-0.35% maximum sulfur content of 0.02% 0.02% maximum phosphorus content of 0.03% 0.03% maximum silicon content of 1.0% 0.8% maximum manganese content of 2.0% 1.5% tungsten content of 0.5% maximum 0.8% maximum copper content of 0.5% 0.75% 5. mechanical properties requirements are as follows Material 2205 alloy 2507

Nitrogen flow meter supplier | What is Lind GmbH in Germany | Flow meter distributor

1. Someone who understands the English language of valve technology can help.

『SILVER Official Website SERVICE』