Current position > Contact Us
Quick Answer: A magflow meter with an integrated smart display gives local flow rate, totalized volume, empty pipe alarm, and diagnostic codes. Silver Automation Instruments supplies electromagnetic flow meters with backlit LCD or TFT displays and 4-20 mA HART plus RS485 MODBUS RTU outputs. Send your pipe size, flow range, and fluid type for a quote.
Engineers do not want a separate loop-powered indicator when panel space is tight. A compact magflow meter with a built-in display solves that panel space problem. The screen shows instantaneous flow in m3/h, totalized volume in m3, reverse flow indication, and alarm codes. For batching systems, a bright display near the fill valve lets operators read the batch total without walking to the PLC HMI.
We have supplied DN25 to DN300 magflow meters with integrated displays to water treatment plants in Vietnam, chemical dosing skids in the UAE, and food processing lines in Indonesia. The most common panel request is a simple two-line LCD with totalizer and flow rate. The second request is a TFT display that shows a trend curve for empty pipe detection and electrode coating.
Silver Automation Instruments offers three display configurations. The basic version uses a backlit LCD with two lines and a four-button keypad. This configuration works well for clean water, raw water intake, and chilled water loops. The second version uses a TFT color display with local configuration menus in English, Spanish, or Portuguese. The third version is a remote mount display. The sensor can sit in a wet pit or a tight pipe rack while the display mounts on a panel door up to 10 meters away.
For automation layouts, the remote mount option often solves a real problem. Last year a water utility in the Philippines installed the sensor in a below-grade chamber. The display went into the control cabinet at grade level. Operators read flow without opening the chamber. The empty pipe alarm also stayed visible on the local display.
The integrated electronic smart display on a magflow meter should not be a passive indicator. The display should also carry the signal outputs your automation system needs. Our standard magflow meters include 4-20 mA HART, pulse output, and RS485 MODBUS RTU. Some models include two relay outputs for high flow, low flow, empty pipe, or reverse flow alarms.
In practice, many SMEs in Southeast Asia and the Middle East run the 4-20 mA signal to a PLC analog input and keep MODBUS as a backup for diagnostics. The local display shows the same process variable as the PLC. Loop checks become faster. You can compare the display value against the SCADA value without a handheld communicator.
For a reliable reading, provide the pipe size in DN, normal and maximum flow rate, fluid type, temperature, and pressure. Magflow meters need a minimum conductivity. Most water-based fluids work well above 5 µS/cm. Pure demineralized water or some solvents may need a different meter type.
Line size is not the same as flow range. A DN100 pipe moving only 3 m3/h will produce a weak signal. We often recommend a reduced bore magflow meter for low flow velocity. The display should also be set for the correct units. Our factory default is m3/h and totalized m3. If you need liters per minute or kg/h, tell us before dispatch.
Keep the display face accessible. The standard sensor has IP67 protection. The display housing is IP67 or IP68 on selected models. For outdoor installations in the Gulf region, use a sunshade. Direct sunlight can reduce LCD contrast. The TFT display handles sunlight better than the basic LCD.
Here is the thing. Most engineers skip the grounding check during commissioning. Earth the sensor properly. Electromagnetic flow meters can pick up stray voltage from VFD cables. Use separate cable trays for signal and power wiring. Poor grounding shows up as unstable flow on many customer sites. A simple ground ring or grounding electrode fixes most cases.
Can I use a magflow meter for seawater desalination feed lines?
Yes. Specify 316L electrodes or Hastelloy C electrodes with a PTFE or EPDM liner. Send salinity and temperature so we can confirm the liner and electrode match.
What output does the integrated smart display provide?
The standard model includes 4-20 mA HART, pulse output, and RS485 MODBUS RTU. Relay outputs for alarms are optional.
Can the display be mounted away from the sensor?
Yes. Remote mount versions are available with cable lengths up to 10 meters as standard. Longer cable runs can be quoted.
What pipe sizes do you cover?
We supply magflow meters from DN15 to DN2000. Small DN15 and DN20 meters suit chemical dosing. Large DN600 to DN2000 meters suit raw water intake and irrigation lines.
How do I get a price?
Send your pipe size in DN, flow range in m3/h, fluid type, temperature, and pressure. Contact Silver Automation Instruments at Tel: +86-25-68650347, Whatsapp: +86-25-52155837, or WeChat: +86 15365082610. You can also check the magflow meter range at flow-meter.com.au.
